Operating Instructions and Parts Manual 15-inch Thickness Planer Models JWP-15DX and JWP-15HH JET 427 New Sanford Road LaVergne, Tennessee 3
10This machine’s power cord must be fitted with an appropriate UL/CSA listed 230 Volt plug (similar to the one shown in Figure 9), or it can be “hard
119.0 Adjustments Disconnect machine from power source before making adjustments (except feed rate). 9.1 Belt tension Inspect the tension of th
129.3 Table Rollers Your planer is supplied with two table rollers (Figure 14) which turn as the stock is fed into the machine, thus reducing fricti
13Care must be exercised in setting knives into the cutterhead. Replace all three knives at the same time. Proceed as follows: 1. Disconnect machine
149.7 Inspect work table parallel to cutterhead The work table is set parallel to the cutterhead at the factory and no further adjustment should be
154. Remove the chain from the particular sprocket on the corner of the base that you need to adjust. 5. Turn the sprocket by hand to bring that cor
169.13 Height of infeed roller, chipbreaker and outfeed roller The infeed roller, chipbreaker and outfeed roller are adjusted at the factory. The he
179.16 Chipbreaker height The chipbreaker breaks off the larger chips before the stock reaches the cutterhead. Use the gauge block and a .02" (
18The gear box has two feed speeds. These are set by pulling out or pushing in the shift lever (Figure 30). Always change feed speed while the machin
19Remove resin and other accumulations from feed rollers and table with a soft rag and non-flammable solvent. Periodically check all the chains for p
21.0 Warranty and service JET® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please c
20The item numbers on this chart are referenced to the surrounding Figures on pages 19 and 20. Figure 33 Figure 35 Figure 34 Figure 36 No. Posit
2111.0 Troubleshooting the JWP-15DX/15HH 11.1 Performance problems Trouble Probable Cause Remedy Snipe. (NOTE: Snipe can be minimized until negli
2211.2 Mechanical and electrical problems Trouble Probable Cause Remedy Uneven depth of cut side to side. Knives are worn. Replace knives. Cutterh
23Trouble Probable Cause Remedy Machine will not start/restart or repeatedly trips circuit breaker or blows fuses. (continued) Motor starter failur
2412.1.1 Base Assembly – Exploded View
2512.1.2 Base Assembly – Parts List Index No. Part No. Description Size Qty 1 ... JWP15H-201 ...Base ...
2612.2.1 Table Assembly – Exploded View
2712.2.2 Table Assembly – Parts List Index No. Part No. Description Size Qty 1 ... JWP15H-101 ...Middle Table ...
2812.3.1 Gear Box Assembly – Exploded View
2912.3.2 Gear Box Assembly – Parts List Index No. Part No. Description Size Qty 1 ... JWP15H-301 ...Gear Box ...
32.0 Table of contents Section
3012.4.1 Stand and Motor Assembly – Exploded View
3112.4.2 Stand and Motor Assembly – Parts List Index No. Part No. Description Size Qty 1 ... PJN-S01 ...Base ...
3212.5.1 Head Assembly – Exploded View
3312.5.2 Head Assembly – Parts List Index No. Part No. Description Size Qty 1 ... JWP15H-001 ...Head Casting...
3458 ... JWP15H-058 ...Key...4x4x10 ... 1 59
3513.0 Electrical Connections A1ManAuto95969798RORA214NO6T34T22T13L21713NO5L31L1
36 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com
4 3.0 Safety warnings 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warning
5 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention. Looking arou
64.0 Introduction This manual is provided by JET covering the safe operation and maintenance procedures for a JET Model JWP-15DX and JWP-15HH Planer
7 Contents of fastener bags (Figure 2): A – (for installing Handwheel) 1 Direction Label 1 Hex Nut 1 Flat Washer 1 Key B – (for installing Exten
87.0 Assembly Tools required for assembly: Forklift or hoist with slings Open-end wrenches (provided) Hex wrenches (provided) 16mm open-end wrench
97.3 Extension tables The JWP-15DX extension tables have rollers; the JWP-15HH extension tables are cast iron. Both are installed in the same manner
Commentaires sur ces manuels