Operating Instructions and Parts Manual 10x15-inch Woodworking Lathe Models JWL-1015, JWL-1015VS model JWL-1015VS shown WALTER MEIER (Ma
10To remove spur center (Figure 6): Hold spur center to prevent it falling. (Use a rag to protect your hand from the sharp edges). Insert knockout ro
11 Figure 8 8.2 Extension cords The use of extension cords is discouraged – try to position equipment within reach of the power source. If an exten
12 Figure 10 The clamping system has been properly adjusted by the manufacturer. If in the future it does not properly lock tailstock in position, re
139.4 Index pin Refer to Figure 16. Indexing is used to create evenly spaced features in a work piece, while keeping the lathe spindle locked; for e
1411.2 Turning Tools If possible, select only quality, high-speed steel turning tools. High-speed steel tools hold an edge and last longer than ordi
15Put a dimple in the stock with an awl or nail, or use a spring-loaded automatic center punch. 2. Extremely hard woods may require kerfs cut into t
16Always cut down-hill, or from large diameter to small diameter. Always work toward the end of a work-piece, never start cutting at the end. Figure
17Parting Off 1. Use parting tool. 2. Adjust lathe speed to lower RPM for parting through a workpiece. 3. Place tool on tool support and raise the
18Checks and Cracks Green wood will check and crack. For best results, leave logs in as long a length as you can handle. As the material starts to dr
19and pointed toward the four o'clock position, as shown in Figure 28. Figure 28 6. Use the left hand to control cutting edge of gouge, while
21.0 Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of ou
20 Figure 29 12.3 Belt replacement Refer to Figures 30 through 32. 1. Disconnect lathe from power. 2. Open pulley access doors. 3. Release belt t
2113.0 Recommended Lathe Speeds (per diameter of workpiece) Diameter of Work Roughing RPM General Cutting RPM Finishing RPMUnder 2” 1520 3000 3
2215.0 Optional accessories These accessory items, purchased separately, can enhance the functionality of your lathe. Contact your dealer to order,
2316.0 Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Mo
2416.1.2 JWL-1015 Lathe – Parts List Index No Part No Description Size Qty ... JWL1015-HA ... Headstock Assembly (incl
25Index No Part No Description Size Qty 55 ... JWL1221VS-223 ... Handwheel ...
2616.2.1 JWL-1015VS Lathe – Exploded View
2716.2.2 JWL-1015VS Lathe – Parts List Index No Part No Description Size Qty ... JWL1015VS-HA ... Headstock Assembly (inclu
28Index No Part No Description Size Qty 55 ... JWL1221VS-223 ... Handwheel ...
2917.0 Electrical Connections JWL-1015 JWL-1015VS (variable speed model) LED LightMAX
32.0 Table of contents Section Page 1.0 Warranty and Service ...
30This page intentionally left blank
31This page intentionally left blank
32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettoo
4 3.0 Safety warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the wa
525. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands. 26. Do not stand on the m
65.0 Features and nomenclature – JWL-1015/1015VS lathes Figure 1: Variable speed model shown 1. Headstock 2. Headstock handwheel 3. Index pin
76.0 Specifications Model number ... JWL-1015 ...
86.1 Hole pattern – JWL-1015/1015VS lathes Figure 2 Clearance hole spacing for mounting lathe
97.0 Setup and assembly Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent.
Commentaires sur ces manuels