JET 719100 Manuel d'utilisation et d'entretien télécharger pdf (Page 4)

3.0 Safety warnings

1. Read and understand the entire owner's

manual before attempting assembly or

operation.

2. Read and understand the warnings posted on

the machine and in this manual. Failure to

comply with all of these warnings may cause

serious injury.

3. Replace the warning labels if they become

obscured or removed.

4. This lathe is designed and intended for use by

properly trained and experienced personnel

only. If you are not familiar with the proper and

safe operation of a lathe, do not use until

proper training and knowledge have been

obtained.

5. Do not use this lathe for other than its intended

use. Do not turn materials other than wood on

this lathe. If used for other purposes, Walter

Meier (Manufacturing) Inc., disclaims any real

or implied warranty and holds itself harmless

from any injury that may result from that use.

6. Always wear approved safety glasses/face

shields while using this lathe. Everyday

eyeglasses only have impact resistant lenses;

they are not safety glasses.

7. Before operating this lathe, remove tie, rings,

watches and other jewelry, and roll sleeves up

past the elbows. Remove all loose clothing

and confine long hair. Non-slip footwear or

anti-skid floor strips are recommended. Do not

wear gloves.

8. Some dust created by power sanding, sawing,

grinding, drilling and other construction

activities contain chemicals known to cause

cancer, birth defects or other reproductive

harm. Some examples of these chemicals are:

• Lead from lead based paint.

•

Crystalline silica from bricks, cement and

other masonry products.

•

Arsenic and chromium from chemically

treated lumber.

Your risk of exposure varies, depending on

how often you do this type of work. To reduce

your exposure to these chemicals, work in a

well-ventilated area and work with approved

safety equipment, such as face or dust masks

that are specifically designed to filter out

microscopic particles.

9. Do not operate this machine while tired or

under the influence of drugs, alcohol or any

medication.

10. Make certain the switch is in the OFF position

before connecting the machine to the power

supply.

11. Make certain the machine is properly

grounded.

12. Make all machine adjustments or maintenance

with machine unplugged from power source.

13. Remove adjusting keys and wrenches. Form a

habit of checking to see that keys and

adjusting wrenches are removed from the

machine before turning it on.

14. Keep safety guards in place at all times when

the machine is in use. If removed for

maintenance purposes, use extreme caution

and replace the guards immediately after

completion of maintenance.

15. Check damaged parts. Before further use of

the machine, a guard or other part that is

damaged should be carefully checked to

determine that it will operate properly and

perform its intended function. Check for

alignment of moving parts, binding of moving

parts, breakage of parts, mounting and any

other conditions that may affect its operation.

A guard or other part that is damaged should

be properly repaired or replaced.

16. Provide for adequate space surrounding work

area and non-glare, overhead lighting.

17. Keep the floor around the machine clean and

free of scrap material, oil and grease.

18. Keep visitors a safe distance from the work

area. Keep children away.

19. Make your workshop child proof with padlocks,

master switches or by removing starter keys.

20. Give your work undivided attention. Looking

around, carrying on a conversation and “horse-

play” are careless acts that can result in

serious injury.

21. Maintain a balanced stance at all times so that

you do not fall into the spindle or other moving

parts. Do not overreach or use excessive force

to perform any machine operation.

22. Use the right tool at the correct speed and

feed rate. Do not force a tool or attachment to

do a job for which it was not designed. The

right tool will do the job better and more safely.

23. Use recommended accessories; improper

accessories may be hazardous.

24. Maintain tools with care. Keep turning chisels

sharp and clean for the best and safest

performance. Follow instructions for lubricating

and changing accessories.

1 2 3 4 5 6 7 8 9 ... 31 32

Commentaires sur ces manuels

Pas de commentaire

JET 719100 Manuel d'utilisation et d'entretien Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Tours JET 719100