JET 708458K Manuel d'utilisation et d'entretien

Operating Instructions and Parts Manual 8-inch Woodworking Jointer Models JJ-8CS and JJ-8HH Model JJ-8CS Model JJ-8HH

10Installing Cutterhead Guard Orient guard (Fig. 8) in proper position and insert post into hole in table. Tighten lock screw (A, Fig. 8). Install

11The JJ-8CS and JJ-8HH jointers are rated at 230V, single phase only. Confirm that the power at the source is compatible with the jointer before in

1245° Fence Adjustment Note: Whenever making an adjustment to the fence, lift the fence up slightly after releasing the lock handle to avoid scratchi

135. When the outfeed table and blade number one (or knife insert) are the same height, tighten table lock screw. After the outfeed table has been

14Removing and Replacing Knives (JJ-8CS only) Disconnect the machine from the power source before making any adjustment or repair. All knife lock bo

15Each knife insert has an etched reference mark so that you can keep track of the rotations. IMPORTANT: When removing or rotating inserts, clean saw

16For jointing and planing cuts pressure is directed three ways; into the fence to ensure a square cut, forward to advance the stock, and downward to

17Taper Cut Taper cuts require the removal of the cutterhead guard. Use extreme caution when making taper cuts and replace the guard immediately a

18Maintenance Lubrication 1. Use a good grade of light grease on the steel adjusting screws located in the raising and lowering mechanisms of the wo

196. Lift assembly straight up. Studs (F, Fig. 34) will still be attached to the bearing housings. 7. Before replacing the cutterhead back into th

2Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Aut

20Replacement Parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848, Monday

21Fence Assembly (all models) Parts List – Fence Assembly (all models) Index No. Part No. Description Size Qty 1 ... JC-F01 ...

22Bed Assembly (all models)

23Parts List – Bed Assembly (all models) Index No. Part No. Description Size Qty 1 ... JC-T01 ...Base ...

24Stand and Motor Assembly (JJ-8CS only)

25Parts List – Stand and Motor Assembly (JJ-8CS only) Index No. Part No. Description Size Qty 1 ... JC-M01W ...Stand ..

26Stand and Motor Assembly (JJ-8HH only)

27Parts List – Stand and Motor Assembly (JJ-8HH only) Index No. Part No. Description Size Qty 1 ... JJ8HH-301 ...Stand ..

28Parts List – Cutterhead Assembly (JJ-8CS only) Index No. Part No. Description Size Qty 1 ... JC-C01 ...Cutterhead

29Parts List – Cutterhead Assembly (JJ-8HH only) Index No. Part No. Description Size Qty ... JJ8HH-CA ...Cutterhead As

3Table of Contents Warranty and Service ...

30Electrical Connections (JJ-8CS only) BLACKWHITEWHITEMotorBLACKGREEN1817WHITEGREENBLACK979896 95WHITEBLACKGREENGREENGROUNDA26T34T22T114NO6T34T22T1

31Electrical Connections (JJ-8HH only)

32 WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools

4 Warning 1. Read and understand the entire owners manual before attempting assembly or operation. 2. Read and understand the warnings posted on th

5 21. Make your workshop child proof with padlocks, master switches or by removing starter keys. 22. Give your work undivided attention. Looking aro

6Levers and Controls Specifications Model JJ-8CS JJ-8HH Stock Number – Bed and Stand Kit ... 708458K...

7Unpacking and Cleanup Contents of Shipping Cartons Note: Unit shipped in two cartons. Stand Carton 1 Stand with Motor 1 Stand Door 1 Dust Chute wi

8 Cutterhead knives are dangerously sharp! Use extreme caution when cleaning. 4. Apply a thin layer of paste wax to the bright surfaces of the fence

9Installing Handwheels 1. Remove protective tape from shaft, and remove screw and washer. 2. Press handwheel (A, Fig. 4) onto shaft, aligning the k